View, Review And Advice On The Most Quality Of Building Stones.

Tag: contribution

stone foundations

How to build stone foundations?

Any building that is built must have a good foundation in order to stand up. The foundation transfers the weight and incoming force of building to the ground by the used columns. In each area depending on the weather conditions, the foundations are different. For each building a special foundation is built according to its plan and number of floors. The foundations are different and each one is built with different materials. For example concrete foundation is built with concrete. Also for building stone foundations it is used only small and big stones.
The stone foundation has a long history and many historical buildings have stone foundations. This kind of foundation has a high strength . The cost of it is very low and we can say it has no cost compared to some of the foundations. In fact, you just have to buy crushed stone.
Because stone has a great durability, this kind of foundation can be used in many different areas.
Stone foundations are being built in two ways according to the pressure and weight they have.
Buildings with low pressure and weight use stone foundation with lime mortar mix. In the other hand buildings with high pressure and weight, use stone foundation with cement sand mix.

stone foundations

Steps for building stone foundation :
We want to explain the general method of building stone foundation step by step. With this method you can save money in building costs.
1. Dig a peripheral fence around your building.
This fence should be 45cm wide and its depth must be as much as not to become frozen. Use pocket for digging and shovel for taking the soil out. The soil can be used for making the foundation’s slope. Then smooth the fence floor by a square shovel.
2. First place large stones in the dug fence.
First you can put all the large stones into the fence. Then use smaller ones to fill the fence.
3. Tighten the stones.
You can use a hammer for braking the stones if necessary. Note that you can use asphalt pieces too. If you want to use old concrete parts in your foundation, first divide them into flat pieces by hammer.
4. Fill the fence with crushed stone and kill that hard.
In this step you can spread the crushed stones with your hands to fill the entire foundation holes.
5. Install the necessary pipes and surround them with stone.
At this point, you can use 2cm pipe for clean water. Also you can use 7.5cm pipe for building’s wastewater. May be in the future these pipes will be used.
6. Use your favorite connector wall to increase the structure’s height.
If you want to use the same traditional way for building stone foundations, build your connector wall with soil bags. You can place barbed wire between soil bags to stick them together for more strength. In the standard bag walls, the lowest rows are filled by mashed bags and the upper ones by sustainable mixture of soil.
Once finished, the walls are completely covered to protect from bags and not easily worn. Because these bags are so wide, we can use them to build strong walls.
Note : The stone used for building foundation has to be healthy and be from different types of broken stone. Polished and circular stones are not suitable for building foundations because they make them unstable.

building stone

Building Appearance

The first thing that is considered in each building is the building’s appearance. Design and use of high quality materials has been considered for long-standing notice. In addition, due to natural disasters such as floods, earthquakes and fires Building Resistance is one of the most important issues to consider. It seems that one of the best materials that is well-liked by the general public is stone.

Stone is considered one of the best products for posterity. The use of stone in the facade of the building, in addition to the beauty of the building, is also effective in raising the quality of the building’s facade. In addition, the safety of stone facades, especially in fires, is much more than the other materials used today. It’s safe to say that the use of stone in recent years has grown dramatically in the rest of the world. For this reason, it seems that standards should be considered for the use of stone in the facade of the building. If the stone does not have the required standards, it can not be used in this part of the building, which is actually a manifestation of a building.
In many countries, attention to the standard stone is very important. If stone placement standards are well considered, many of the problems in the stone facade will be resolved. In fact, the use of inert stones and even some of the stones that are suitable for use in the facade of the building also causes us a lot of problems. If all countries are committed to these standards, we will see more beautiful and more spectacular shots.
One of the problems created for the facade of the building is the deterioration of the stone. In fact, stone faces may deteriorate for various reasons, and it is therefore better to use stones that do not suffer from this problem. This area is different in the region and should be considered on the basis of experience as well as academic information on stony faces.
The measurement of the quality index, as well as those related to the stanza standard, varies from country to country. Even in many countries that have several standard types, the standard stones differ considerably.

stony face
Generally, companies that define the standard stone format examine this standard in terms of physical and mechanical properties, including the most important factors to be considered in stone, the amount of abrasion and resistance to wind, Polluting particles and acid rain. These are commonly investigated in the specialized laboratory of stone and experts in this field can, by measuring some parameters, obtain results about the standard of stone. Also, some standards are considered for engineers and architects to consider the constraints required to determine some of the parameters of the stone installed in the building. For example, stone thickness is numerous in different standards and should be considered by engineers and architects. Also, the method of installing, repairing and maintaining the stone is very important and the engineers must stamped according to the standards defined in the area.
Unfortunately, in some countries, the importance of considering different standards for stone facades is unconventional, and this has caused natural stones not to have a good effect on the stoney facade or very soon suffer damage. Of course, the building designer should also be professional and reliable in order to provide a professional, well-liked stone look that can be used for many years to come.
It is hoped that in the coming years architects and engineers will comply with all standards related to the building’s appearance to minimize the damage caused by flood, earthquake and fire.